DryGlide FEET GLIDE TAPE — Ultra-Thin Overlays

Low-Profile Mouse Skate Tape · dryglide.pro · HomeEXTRA

🔥 FPS gods know this — but they’ll never tell you.
They level the feet without raising the LOD.

🧪 The Origin Story — Overlay, not overhaul

I wanted the snap of fresh skates without changing how high the sensor cuts out. So I built an ultra-thin overlay that bonds over worn feet, restores glide, and keeps your muscle memory intact. No bulk. No wobble. No weird edges.

Not factory magic. Just years of testing the first millimeter.

🎯 What it does (feel > theory)

• Low-Profile, Low LOD impact — restores speed while keeping lift-off distance essentially unchanged.
  
  

• Softer Starts — zero stick from stillness.
  
  

• Predictable Stops — fast slide with clean bite when you set the shot.
  
  

• Edge-Safe — beveled feel; resists snagging on pad seams.
  
  

• Dust-Smart Surface — wipes clean in seconds, stays consistent.
  
  

🧩 The Stack: Pad × Feet × Tape = Ultimate Glide Geometry

• On the pad: DryGlide Gaming Elixir Pro → dry, controlled surface.
  
  

• On the feet: FEET POLISH ELIXIR — Pro-Control Serum → ultra-thin control film.
  
  

• Over the skates: FEET GLIDE TAPE → low-profile overlay that preserves your LOD.
  Together: quicker starts, cleaner micro-adjustments, sharper stops — with your sensor behaving exactly how you expect.
  
  

⚙️ Why the pros won’t admit it

✅ Restores glide without re-learning lift-off
✅ Smooths out worn feet and micro-chips
✅ Tuned for glass & hardpads; great on tight-weave cloth*
✅ No residue mess; no gimmicks
*Performance varies by material/texture. Always test first.

✂️ Fit & Thickness

• Ultra-thin profile for minimal LOD change.
  
  

• Pre-cut shapes for popular mice + trim-to-fit sheets for everything else.
  
  

• Rounded-corner geometry to avoid edge catch.
  
  

🧴 How to apply

Clean → Align → Press → Polish → Frag.

1. Clean old feet and surrounding shell (microfiber; a little IPA 70% if needed). Dry fully.
   
   

2. Peel & align overlay flush with the original feet.
   
   

3. Press from center out to set the bond; smooth edges with the applicator.
   
   

4. Polish one pass with a dry cloth. Optional: finish with a micro-coat of FEET POLISH ELIXIR for peak feel.
   
   

5. Test glide. If edges lift, re-press for 5–10 seconds.
   
   

Pro tip for LOD consistency: apply only on the feet (not the bare shell), and keep debris out from under the tape.

🧼 Maintenance

Wipe with a dry microfiber after sessions. If glide fades, a light buff or a tiny pass of FEET POLISH ELIXIR brings it back. Replace the tape when visibly worn.

📦 Included

• DryGlide FEET GLIDE TAPE — Ultra-Thin Overlays (pre-cuts or trim-to-fit sheet)
  
  

• Alignment tool / microfiber / edge applicator
  
  

✍️ Short Description

Ultra-thin mouse-feet overlays that restore speed and control while keeping lift-off distance essentially unchanged. Designed to layer over worn skates and to pair perfectly with DryGlide Gaming Elixir Pro (pad) and FEET POLISH ELIXIR (feet). Pad × Feet × Tape = unfair control.

❓ FAQ

Will it raise my lift-off distance?
The profile is intentionally ultra-thin to keep LOD changes negligible for most sensors and pads.

Does it leave residue if removed?
No messy peel. If any trace remains, a little IPA on microfiber clears it.

Can I use it with glass or metal pads?
Yes—built with hardpads in mind; also works on many tight-weave cloth pads.*

Do I still need FEET POLISH ELIXIR?
For best feel, yes. Tape restores geometry; the elixir fine-tunes friction for softer starts and predictable stops.

Headline blocks (store/landing)

Overlay the feet — keep the LOD.
Thin profile · Softer starts · Predictable stops
The secret synergy: Pad Elixir + Feet Elixir + Glide Tape.

Safety note

For equipment use only. Do not ingest. Keep sealed and away from children. Spot-test first.